BMW G 650 X
High-quality, universal ALTRIDER handlebar riser kit, rising the bar by 30 mm. Elegantly machined from aircraft-grade aluminum, this item has been created to rise a vide variety of motorcycle handlebars. The offset geometry of the clamping faces prevent the bars from rotating, while non-corroding stainless socket head screws and screw head covers keep everything weather-resistantly in place. The risers have been bead-blasted, then finished in an anodized black and feature an engraved ALTRIDER logo. In most situations, their installation is compatible with the OEM wiring and brake/clutch cables, i. e. there is no need to extend or re-route any cables on the bike. Note: It is essential to always check and confirm that the bike has adequate cable and brake line lengths before installing any handlebar risers! The ALTRIDER 30 mm Block Handlebar Risers are designed to fit on any bike with a stock 1-1/8" (28,5 mm) handlebar, parallel OEM bar clamps and an open mounting area. They are quickly and easily installed by using the four included bolts. Specifications 100% designed and made in the USA Machined from 6061 billet aluminum Fit motorcycles with 28.5mm tapered handlebars Optimise the riding position Offset clamp design to ensure a secure clamping force Easy 4-bolt installation Delivery includes all the necessary mounting material and instructions Engraved ALTRIDER logo Available in matte black anodized IMPORTANT: OEM bar clamps must be parallel and sized for M8 bolts in order for these risers to mount properly! Cannot be installed on bikes with angled (eg. V-Shaped) OEM bar clamps! Cannot be installed where the OEM clamping bases are offset (bases must be level)! Manufacturer AltRider3708 Airport Way SouthSeattle, WA 98134-2217, USAHomepageDistribution:AltRiderSpectrumlaan 312665 NM BleiswijkNetherlandsHomepage
Tough and robust fabric hand guard kit by BARKBUSTERS, providing maximum protection against wind and weather. Specifications Stylish fabric hand guard design, lined with a waterproof membrane Delivered in pairs Can be fitted to almost any handlebar set-up Flexes around fairing/windscreen at full steering lock Ideal for faired sports and touring motorcycles Anti-flap design - self-supporting under wind pressure Leaves controls free of interference Maximum cold weather protection Can be fitted to handlebar weights, as well as to hollow handlebars and over existing BARKBUSTERS BHG backbones (available separately) Delivery includes all necessary mounting hardware and instructions Available in black-grey Manufacturer:Rideworx Pty Ltd3/7 Luso Dr, Unanderra NSW 2526, AustraliaHomepageDistribution: offroad-kontor
Tough handguards by BARKBUSTERS made of high-quality carbon fiber, providing excellent protection from the elements. Specifications Delivery includes two handguards and a fastening screw kit Finished with a UV stable gloss-coated resin Can be fitted to all BARKBUSTERS VPS handguard alloy backbones (available separately) NOT recommended for off-road applications! Available in black Manufacturer:Rideworx Pty Ltd3/7 Luso Dr, Unanderra NSW 2526, AustraliaHomepageDistribution: offroad-kontor
High-quality, robust aluminium frame for the mounting of BARKBUSTERS handguards, specifically designed for BMW models (see below). Specifications Delivery includes two frames Made of heat-treated aluminium for added strength and impact protection Complete mounting kit included for easy installation Note: This product does NOT include the corresponding plastic covers! Choose suitable protection from Jet, VPS, Storm or Carbon covers (see below) Suitable for: BMW G650X Challenge / Moto / Country Manufacturer:Rideworx Pty Ltd3/7 Luso Dr, Unanderra NSW 2526, AustraliaHomepageDistribution: offroad-kontor
High-quality BARKBUSTERS plastic handguards for JET-001 and JET-002 (available separately, see below).Fits all BHG-Kits also. Specifications Delivery includes two handguards and a fastening screw kit Available in many different colours (please select from above) Manufacturer:Rideworx Pty Ltd3/7 Luso Dr, Unanderra NSW 2526, AustraliaHomepageDistribution: offroad-kontor
Set of 2 high-quality, practical LED amber light indicators by BARKBUSTERS. Specifications Ideal for use as a turn indicator Can be fitted to the upper surface only of JET guards Can be fitted to the upper and/or lower surface of VPS and STORM guards (all BARKBUSTERS hand guards available separately, see below) E-mark approved as an indicator light 15 super bright LED’s per light Low power draw Substantial increase of visibility to other road users May require optional resistor for correct flash rate (code: LED-RES-001, available separately - see below) NOTE: NOT compatible with the HONDA CRF 1000L Africa Twin electrical system! Manufacturer:Rideworx Pty Ltd3/7 Luso Dr, Unanderra NSW 2526, AustraliaHomepageDistribution: offroad-kontor
Set of 2 high-quality, practical white LED position lights by BARKBUSTERS, specifically designed to be used for the below-mentioned hand guards. Specifications 15 super bright LED’s per light Low power draw Substantial increase of visibility to other road users E-mark approved (no. E8 50R-001526) To be used for the following BARKBUSTERS hand guards (all available separately, see below): JET guards (on upper surface only) VPS and STORM guards (on upper and/or lower surface) Manufacturer:Rideworx Pty Ltd3/7 Luso Dr, Unanderra NSW 2526, AustraliaHomepageDistribution: offroad-kontor
Set of 2 high-quality, practical resistors, specifically designed to be used for the BARKBUSTERS LED Amber Light Indicators if required to correct the flash rate (indicators and handguards available separately, see below). Specifications Resistance: 10 Ohm To fit in conjunction with the BARKBUSTERS LED Amber Light Indicators (available separately, see below) where necessary to correct the flash rate - the recommended flash rate is 90 (+/-30) times per minute Manufacturer:Rideworx Pty Ltd3/7 Luso Dr, Unanderra NSW 2526, AustraliaHomepageDistribution: offroad-kontor
Tough plastic handguards by BARKBUSTERS, providing excellent protection from the elements.Fits all Storm-Kits as a spare and all BHG-Kits as an accessory. Specifications Delivery includes two handguards and a fastening screw kit (Last picture shows package contents) Can be fitted to all BARKBUSTERS VPS handguard alloy backbones (available separately, see below) Available in black and white Manufacturer:Rideworx Pty Ltd3/7 Luso Dr, Unanderra NSW 2526, AustraliaHomepageDistribution: offroad-kontor
High-quality VPS skid plate set by BARKBUSTERS. Specifications Delivery includes two pads Protects the outer edge of the aluminium backbone Adds a stylish finish to the handguard Suitable for VPS and Jet plastics (available separately, see below) Note: Does NOT fit with Storm plastics! Available in black Manufacturer:Rideworx Pty Ltd3/7 Luso Dr, Unanderra NSW 2526, AustraliaHomepageDistribution: offroad-kontor
Tough plastic handguards by BARKBUSTERS with variable height wind deflectors. Specifications Delivery includes two handguards and a fastening screw kit Can be fitted to all BARKBUSTERS VPS handguard alloy backbones (BHG mounting kits) Available in various different colours (please select from above) Other colours on request Manufacturer:Rideworx Pty Ltd3/7 Luso Dr, Unanderra NSW 2526, AustraliaHomepageDistribution: offroad-kontor
The black anodized Vario relocation converter, made of robust, CNC-machined aluminum for mounting 28 mm handlebars, allows a relocation of 50 mm, or even 60 mm with a spacer, from the original handlebar position.Maximum flexibility: Vario handlebar relocations allow for continuous forward and backward adjustment as well as variable height adjustment. The adapters thus offer the greatest possible flexibility when adjusting the steering and thus seating position. For vehicles with a 22 mm handlebar mount for mounting 28 mm handlebarsCorrosion protection thanks to black anodizingVariable handlebar riser and relocation for individual handlebar positioning by 50 mmSpacer for optional rise of an additional 10 mmModel-specific design for the best fitCNC-machined from high-strength aluminum alloy Scope of delivery 2 x Vario handlebar risers/converters2 x spacers (10 mm)Installation instructionsMounting hardware DetailsMaterial: aluminumFinish: anodizedColor: blackTotal weight: approx. 0.5 kg NoteNot approved for use in Germany under the German Road Traffic Licensing Regulations (StVZO).The length of the Bowden cables and brake lines must be checked individually. Approval informationThe ABE certificate booklet supplied with the product must always be carried when riding. This ABE is only valid for the listed models and in compliance with the information in the installation instructions. An entry in the vehicle documents is not necessary if you carry the document with you.