Rallye Parts

High-quality clutch arm guard by ALTRIDER made of tough aluminum, suitable for the Honda CRF 1000 L Africa Twin model (see below). The Africa Twin’s clutch articulation arm and cable sit exposed on the right hand side of the engine case, covered only by an OEM plastic cover which offers virtually no protection. ALTRIDER’s clutch arm guard for the Africa Twin replaces the plastic cover with far greater coverage to this vital area while offering a clean aesthetic to the right side engine case.More robust than other clutch arm covers on the market, ALTRIDER’s design incorporates three unique mounting points to evenly distribute the load from impacts across the guard. With strategic mounting points and bends, the design is engineered to counter the stresses placed on thin aluminum parts after a lifetime of engine vibrations. ALTRIDER’s clutch arm guard is laser-cut out of 2 mm thick 5052 aluminum and features a formed, anodized and grained surface for maximum durability. Specifications ALTRIDER motorcycle accessories are 100% designed and manufactured in the USA Made of anodized aluminum for robust yet lightweight protection Suitable for Honda CRF 1000 L Africa Twin, including Adventure Sports (NON-DCT-only!) Available in silver or black - please select from above Manufacturer AltRider3708 Airport Way SouthSeattle, WA 98134-2217, USAHomepageDistribution:AltRiderSpectrumlaan 312665 NM BleiswijkNetherlandsHomepage

High-quality clutch side engine case cover by ALTRIDER, suitable for the below-mentioned KTM Adventure models. The OEM engine case on the KTM Adventure/R and SA models is made from a thin-walled cast aluminum. This choice helps to save overall weight, but also creates a weak point on a vital piece of the engine. If the KTM Adventure/R and SA models are laid down on their right sides, there is a real danger of the engine case becoming damaged by large debris or even from the brake lever tip bending into it, potentially bursting into the case. Compared to several competitor options made from molded plastic, ALTRIDER created an engine case cover made from a single piece of 3.2 mm aluminum. This exceptionally strong 6061-TG6 aluminum alloy has a tensile strength of at least 42,000 psi (300 MPa) and yield strength of at least 35,000 psi 241 MPa. Rubber backers spread the load of impact, as well as allow the cover to maintain a low profile. Flush stainless steel fasteners and a deburred product prevent scuffing up the rider's boots and pants. The design of the case cover also incorporates the ingenuity of the ALTRIDER Brake Lever Shield, preventing unwanted and unexpected early braking. The close design of the OEM brake lever creates early interference with the rider's boot during braking. This is unique to the KTM Adventure/R and SA models as KTM worked hard to make the large displacement engine still feel narrow, which in turn provided little options for routing the rear brake lever. The lever arm extends into the rider boot area above the brake tip, thus creating earlier-than-expected braking. An outward flange on the ALTRIDER Engine Case Cover prevents accidental engagement of the brake arm while still providing a surface to properly hug the bike with the boot, all without interrupting any feel or ergonomics. Specifications ALTRIDER motorcycle accessories are 100% designed and manufactured in the USA Protects engine case from damage caused by debris or rear brake lever Prevents accidental engagement of rear brake Easy installation with flush mount hardware  Deburred to prevent snagged or caught clothing Made of 3.2 mm (1/8 in.) aluminum Available in black Suitable for KTM 1050 1090 1190 Adventure/R and 1290 SA Manufacturer AltRider3708 Airport Way SouthSeattle, WA 98134-2217, USAHomepageDistribution:AltRiderSpectrumlaan 312665 NM BleiswijkNetherlandsHomepage

High-quality foot brake system by ALTRIDER, offering substantially more braking safety and comfort during off-road riding. Most OEM brake pedals have a single-positioned small footprint, yet most ADV riders substantially change foot positioning as they switch between standing and sitting. If the riders' feet are not already situated correctly on the rear brake pedal, they are potentially doubling reaction time and distance to make what could be a critical stop. This is why all motorcycle racers have 1 or 2 fingers on the front brake lever in photographs. ALTRIDER has taken away this additional hazard with the patent pending DualControl Brake System. There are two parts to the ALTRIDER DualControl Brake System that enhance control and reaction time; a riser and an enlarger plate. Riser When in a seated position, a rider’s bent knee naturally puts the angle of the foot pointed down 90 degrees from the lower leg, while a standing position creates a straighter leg and raises the angle of the foot to a more horizontal position. Using the OEM brake pedal, there is no way to keep the correct brake control position when both sitting and standing. With the ALTRIDER enlarger and riser combined, there are now two levels in which to engage the rear brake, putting the foot in an optimal position, regardless of the riding position.  Enlarger The ever-changing terrain of off-road riding means the rider's entire body is constantly moving and adjusting. The billet aluminum enlarger plate gives the foot a greater surface area to work with, affording the rider more control of the rear brake. The enlarger plate is precision fit to each bike model, ensuring long-term stability. Optional and replaceable grip pins are provided for further customization. Specifications 100% designed and manufactured in the USA Suitable for the Yamaha Tenere 700 (all years) Stainless steel bottom plate and hardware to endure the abrasions of off-road riding 25,4 mm (1 inch) riser height available Pins provided with enlarger for enhanced grip, extras included Kit available in black or silver (please select from above) Patent Pending Manufacturer AltRider3708 Airport Way SouthSeattle, WA 98134-2217, USAHomepageDistribution:AltRiderSpectrumlaan 312665 NM BleiswijkNetherlandsHomepage

High-quality foot brake system by ALTRIDER, offering substantially more braking safety and comfort during off-road riding. Most OEM brake pedals have a single-positioned small footprint, yet most ADV riders substantially change foot positioning as they switch between standing and sitting. If the riders' feet are not already situated correctly on the rear brake pedal, they are potentially doubling reaction time and distance to make what could be a critical stop. This is why all motorcycle racers have 1 or 2 fingers on the front brake lever in photographs. ALTRIDER has taken away this additional hazard with the patent pending DualControl Brake System. There are two parts to the ALTRIDER DualControl Brake System that enhance control and reaction time; a riser and an enlarger plate. Riser When in a seated position, a rider’s bent knee naturally puts the angle of the foot pointed down 90 degrees from the lower leg, while a standing position creates a straighter leg and raises the angle of the foot to a more horizontal position. Using the OEM brake pedal, there is no way to keep the correct brake control position when both sitting and standing. With the ALTRIDER enlarger and riser combined, there are now two levels in which to engage the rear brake, putting the foot in an optimal position, regardless of the riding position.  Enlarger The ever-changing terrain of off-road riding means the rider's entire body is constantly moving and adjusting. The billet aluminum enlarger plate gives the foot a greater surface area to work with, affording the rider more control of the rear brake. The enlarger plate is precision fit to each bike model, ensuring long-term stability. Optional and replaceable grip pins are provided for further customization. Specifications 100% designed and manufactured in the USA Components available separately or as a kit - please select from above Suitable for Yamaha XT 1200 Z Super Tenere Stainless steel bottom plate and hardware to endure the abrasions of off-road riding 25,4 mm (1 inch) riser height available Pins provided with enlarger for enhanced grip, extras included Enlarger and riser available in black or silver (please select from above) Patent Pending Manufacturer AltRider3708 Airport Way SouthSeattle, WA 98134-2217, USAHomepageDistribution:AltRiderSpectrumlaan 312665 NM BleiswijkNetherlandsHomepage

High-quality fork leg guards by ALTRIDER, offering reliable protection for the Yamaha XT1200Z Super Tenere fork. The guards offer a comprehensive perimeter of coverage from forward impacts. A deliberately designed lower radius provides protection from side impacts as well. The interior mounting surface features a foam pad to prevent the fork leg guard from flexing and coming into contact with the fender. Installation takes only a few minutes with the provided hardware. Specifications   All ALTRIDER products are 100% designed and manufactured in the USA 1/16 inch (1.6 mm) strong aluminum construction Delivered in pairs Suitable for the Yamaha XT1200Z  Super Tenere (all model years) Delivery includes all the necessary mounting material Available in black Manufacturer AltRider3708 Airport Way SouthSeattle, WA 98134-2217, USAHomepageDistribution:AltRiderSpectrumlaan 312665 NM BleiswijkNetherlandsHomepage

High-quality side stand foot enlarger by ALTRIDER, offering substantially more safety and comfort on off-road terrain. Custom-made for the BMW F 750 / 850 GS models. Made from 1/8 inch (3.18 mm) stainless steel, this article features a 3D tread to create better traction for the boots and to allow an easy pulling down of the side stand while still on the bike. Even after months of use, the ALTRIDER side stand foot will remain tight because it clamps down on the actual foot of the side stand with Torx fasteners. Specifications 100% designed and manufactured in the USA Offering excellent resistance against corrosion and weather Two-piece design for a perfect fit Minimal weight to avoid accidental deployment during riding Torx fasteners (requires T-25 Torx driver) Delivery includes the necessary mounting material Available in powder-coated black NOTE: The BMW F850 ADV and some standard models are being shipped with different side stands. In this case, the ALTRIDER side stand enlarger will only fit one of these side stands. Therefore, please view the comparison image above in order to determine if this part is suitable for the side stand in question. Manufacturer AltRider3708 Airport Way SouthSeattle, WA 98134-2217, USAHomepageDistribution:AltRiderSpectrumlaan 312665 NM BleiswijkNetherlandsHomepage

High-quality skid plate by ALTRIDER, suitable for the liquid-cooled BMW R1200 GS MY 2016 and up.This skid plate was completely redesigned for the a. m. BMW model. To maintain greater ground clearance, a flat plate of 3/16” (4.76 mm) anodized aluminum is utilized, with no bolts on the bottom side to snag, saving over 1 inch of ground clearance. The plate was designed to be extremely narrow at the bottom to maintain the great cornering ability of the bike. From the leading front corner of the headers to just before the rear tire, the entire bottom side of the motor is shielded from impact. Even the catalytic converter is safeguarded. The ALTRIDER skid plate is the only design on the market that doesn’t rely on the engine as a mounting point. The front of the ALTRIDER plate gets its brute strength from 3/16” (4.76 mm) stainless steel brackets that mount directly to the frame. The brackets are secured with two sturdy M12 torx frame bolts, preventing the flange from pivoting on impact. Another key innovation of the ALTRIDER design are the rear mounting points. These long brackets have more leverage, allowing impacts to create shearing or bending forces that break the mount. The ALTRIDER skid plate is held in place with two custom-machined fasteners that replace the center stand pins, lowering the mounting point by a notable 4” which dramatically reduces leverage. Specifications ALTRIDER motorcycle accessories are 100% designed and manufactured in the USA Made of 3/16” (4.76 mm) hand TIG welded anodized aluminum Protects entire bottom side of the liquid cooled motor, including headers and catalytic converter Oil change does not require removal of skid plate One-piece unit that provides tire to tire protection Simple to install All stainless steel hardware is provided Patent pending Available in black NOTE: Does not fit any BMW R1200 GS Adventure models! Manufacturer AltRider3708 Airport Way SouthSeattle, WA 98134-2217, USAHomepageDistribution:AltRiderSpectrumlaan 312665 NM BleiswijkNetherlandsHomepage

This high-quality ALTRIDER skid plate suitable for the below-mentioned Husqvarna and KTM models is laser cut from aluminum with an anodized finish that is extremely resistant to weathering. The intelligent design features large radius corners and flared edges to provide absolute coverage for the motor, clutch pack, and stator while maintaining exceptional strength. The skid plate also provides coverage for the side stand mount, eliminating the need for a side stand relocation kit. Special consideration was made to preserve the impressive ground clearance and turning radius of the Husqvarna / KTM.  The front of the skid plate mounts via steel brackets that utilize OEM mounting points, whereas the rear brackets are made of 3/16" (4.76 mm) aluminum. With the ALTRIDER design being the only one to provide anti-clocking engagement points at the rear; what this means in terms of protection is this design will resist rearward energy by interfacing the frame centerstand stops. The centerstand mounts are the strongest locations on the frame, originally engineered to take massive loads. Prevent the plate from rotating rearward is critical, without ANTI-CLOCKING the rock impacts will push the skid plate back and up into the motorcycle causing damage. ALTRIDER created the only design on the market to prevent this with the anti-clocking mounts. Specifications All ALTRIDER motorcycle accessories are 100% designed and manufactured in the USA Made of anodized aluminum that protects front and bottom of the motor from trail debris Front and rear mounts for superior strength Fits both the Adventure and Adventure R Available in silver or black - please select from above Suitable for: Husqvarna 901 Norden 2022+ KTM 790 Adventure/R  2019-2022 KTM 890 Adventure/R  2019-2022 NOTE: Skid plate does NOT fit with a center stand installed!              Also does not fit any KTM-models from MY 2023! Manufacturer AltRider3708 Airport Way SouthSeattle, WA 98134-2217, USAHomepageDistribution:AltRiderSpectrumlaan 312665 NM BleiswijkNetherlandsHomepage

High-quality skid plate by the renowned US manufacturer ALTRIDER, suitable for the Yamaha Super Tenere XT1200Z. Rocks and debris are no match for this extremely robust skid plate featuring hand TIG welds and stainless hardware. Constructed of 1/8 inch (3.175 mm) powder coated aluminum, it reaches high on the left hand side to protect the stator, and provides extensive coverage of the headers on the right. The skid plate must be removed to change the oil filter. If using an aftermarket oil filter, it must be the same 2.5 inch (63.5 mm) length as the OEM one to avoid interference. However, the oil alone can be changed with the skid plate installed. Specifications All ALTRIDER products are 100% designed and manufactured in the USA Made of 1/8 inch (3.175 mm) powder coated aluminum with hand TIG welds 1/8 inch (3.175 mm) powdered coated steel hand TIG welded brackets replace the thin stamped sheet bracket to resisting bending upon impact The rear bracket is constructed from 3/16 inch (4.7625 mm) powdered coated steel and utilizes two mounting points on each side to resist pivoting upon impact Plate to be fixed on 4 OEM mounts for a better force distribution and long-term durability Various cutouts for an improved engine heat dissipation Smooth surface to facilitate sliding over obstacles Compatible with Yamaha Super Tenere XT1200Z (2010-current) Compatible with both ES and non-ES versions Available in silver and black - please select from above Note: The ALTRIDER skid plate for Yamaha Super Tenere will NOT work with the OEM Yamaha crash bars because of the interference with the crossbar on the crash bars. The skid plate will mount up, but the cross bar will have to be removed! Manufacturer AltRider3708 Airport Way SouthSeattle, WA 98134-2217, USAHomepageDistribution:AltRiderSpectrumlaan 312665 NM BleiswijkNetherlandsHomepage

High-quality voltage regulator guard by ALTRIDER, suitable for the below-mentioned Honda models. When venturing off the beaten paths, it is important to keep any bike’s vitals protected from stray branches, flying rocks or anything else. That includes the voltage regulator, an integral component responsible for maintaining the battery charge and keeping the bike’s electrical system up and running. ALTRIDER’s voltage regulator guard for the Honda Africa Twin is an upgrade from the stock guard that leaves the voltage regulator completely exposed to debris from the rear tire and chain. The guard offers comprehensive protection in the form of a sturdy 1/8 inch (3.2 mm) thick piece of laser-cut aluminum. It easily mounts to the OEM mounting points with the included stainless steel hardware. Specifications ALTRIDER motorcycle accessories are 100% designed and manufactured in the USA Made of 1/8" (3,2mm) anodized aluminum for robust yet lightweight protection Mounts to OEM mounting points with included stainless steel hardware Available in silver or black - please select from above Suitable for: Honda CRF 1000 L Africa Twin Standard                 from MY 2016 Honda CRF 1000 L Africa Twin Adventure Sports   from MY 2018 Manufacturer AltRider3708 Airport Way SouthSeattle, WA 98134-2217, USAHomepageDistribution:AltRiderSpectrumlaan 312665 NM BleiswijkNetherlandsHomepage

High Quality-Skidplate made of extreme sturdy HDPE-Plastic.fits the following models:Honda CRF 250 L                  2013 - 2016Honda CRF 250 L ABS          2017 - 2018Honda CRF 250 L ABS Rally 2017 - 2018 Manufacturer AXP Racing SARL28 RUE DE LA REPUBLIQUE 59560 - COMINES, FranceHomepageDistributionPaaschburg & Wunderlich GmbHAm Alten Lokschuppen 10a 21509 Glinde, GermanyHomepage

High-quality footrest extensions by GLOBESCOUT, replacing the original pegs of the below-mentioned KTM and Husqvarna models. Specifications Delivery in pairs Including all necessary mounting hardware Available in blue anodized aluminiumStainless steel set screws Fits KTM SX/EXC all and Husqvarna TE/TC from MY 2014 Manufacturer YILDIZ BRONZ Ltd.Davutpaşa C. 22/5234010 Topkapı / Istanbul, TürkiyeHomepageDistributionoffroad-kontor

High-quality, 100% waterproof bolt-on fender pack by KRIEGA. Ideal for carrying safety equipment, small tools, dry gloves etc. on a motorcycle. Specifications  Material: 1000D Dupont® Cordura® Ultra-tough, abrasion-resistant RHINOTEK fabric on base with 4 x heavy-duty rivets DRYPACK = taped-seam liner, fixed with Velcro®  100% waterproof Size: 200 mm x 175 mm x 70 mm (L x W x H) Volume: 2.5 litres Velcro® closure strap 10-year guarantee Delivery includes: 4 x CNC 6061-T6 alloy fasteners with nylon spacer washers 4 x stainless steel fasteners 1 drilling guide (product packaging) Fitting  Remove the white liner (Velcro® top edge) and remove the bag from the packaging The product packaging is designed to be used as a drilling guide  Line up the guide on the rear fender and drill 4 x 6mm diameter holes Use the optional nylon washers to ensure that the threaded fastener is below the top surface of the alloy fastener (prevents damage to the internal waterproof liner/foam) Tighten anti-clockwise and always use thread lock Allow 24 hours to dry Manufacturer Generator NPD LtdUnit 5 Deeside Point, Tenth AvenueZone3 Deeside Ind. Park, CH5 2UA , United KingdomHomepageDistributionGermot GmbHDaimlerstraße 463303  DreieichGermanyHomepage

SM-Line Plastic Front FenderPolisport plastics are made from injected plastic developed in-house. All plastics feature DGP (Durable Polypropylene Gloss), whose main advantages are high strength and a beautiful glossy finish.Identical to the plastics used in MXGP Manufacturer Polisport Plásticos S.A.Travessa da Zona Industrial nº2 Vila Cova de Perrinho 3730-601 - Vale de Cambra, PortugalHomepageDistributionJohannes J. Matthies GmbH & Co. KGHammerbrookstr. 97 20097 Hamburg, GermanyHomepage