Electricity

Set of 2 high-quality, practical LED amber light indicators by BARKBUSTERS. Specifications Ideal for use as a turn indicator Can be fitted to the upper surface only of JET guards Can be fitted to the upper and/or lower surface of VPS and STORM guards (all BARKBUSTERS hand guards available separately, see below) E-mark approved as an indicator light 15 super bright LED’s per light Low power draw Substantial increase of visibility to other road users May require optional resistor for correct flash rate (code: LED-RES-001, available separately - see below) NOTE: NOT compatible with the HONDA CRF 1000L Africa Twin electrical system! Manufacturer:Rideworx Pty Ltd3/7 Luso Dr, Unanderra NSW 2526, AustraliaHomepageDistribution: offroad-kontor

Set of 2 high-quality, practical white LED position lights by BARKBUSTERS, specifically designed to be used for the below-mentioned hand guards. Specifications 15 super bright LED’s per light Low power draw Substantial increase of visibility to other road users E-mark approved (no. E8 50R-001526) To be used for the following BARKBUSTERS hand guards (all available separately, see below): JET guards (on upper surface only) VPS and STORM guards (on upper and/or lower surface) Manufacturer:Rideworx Pty Ltd3/7 Luso Dr, Unanderra NSW 2526, AustraliaHomepageDistribution: offroad-kontor

Set of 2 high-quality, practical resistors, specifically designed to be used for the BARKBUSTERS LED Amber Light Indicators if required to correct the flash rate (indicators and handguards available separately, see below). Specifications Resistance: 10 Ohm To fit in conjunction with the BARKBUSTERS LED Amber Light Indicators (available separately, see below) where necessary to correct the flash rate - the recommended flash rate is 90 (+/-30) times per minute Manufacturer:Rideworx Pty Ltd3/7 Luso Dr, Unanderra NSW 2526, AustraliaHomepageDistribution: offroad-kontor

High-quality brake light and clutch switch by JMP, suitable for the below-mentioned motorcycle models. In terms of shape and function, all JMP brake light and clutch switches correspond to the OEM parts. Suitable for:  Suzuki DL 250 A V-Strom ABS      2017-2021 DL 650 A V-Strom ABS      from MY 2012 DL 650 XT A V-Strom ABS from MY 2015 Yamaha WR 125 R/X                 2009-2017 XT 660 Z Tenere         2008-2016 XTZ 700 Tenere ABS  from MY 2019 Manufacturer Johannes J. Matthies GmbH & Co. KGHammerbrookstr. 97 20097 Hamburg, GermanyHomepageDistributionoffroad-kontor

High-quality brake light switch by JMP, suitable for the below-mentioned Honda models. In terms of shape and function, all JMP brake light switches correspond to the OEM parts. Suitable for: Honda CB 500 X                             2013+ CRF 250 L/M/R/X/Rally      2013-2018 CRF 300 L/Rally                  2021+ CRF 450 L                           2019+ CRF 1000 L Africa Twin     2016-2020 Manufacturer Johannes J. Matthies GmbH & Co. KGHammerbrookstr. 97 20097 Hamburg, GermanyHomepageDistributionoffroad-kontor

Set of 2 high-quality heated grips by JMP, featuring 5 adjustable heating levels. Specifications Length of grips: 120 mm each 12V operation  Electronic control switch to be mounted either by screws or adhesion Suitable for 22mm handlebars Grips are open-ended for fixing bar weights etc. Delivery includes blanking caps and grip glue   Grip rubber compound is resistant to environmental influences and heat  Heating power adjustable as follows: Performance level 1: 41,85 W Performance Level 2: 43,74 W Performance Level 3: 44,96 W Performance Level 4: 45,5 W Performance Level 5: 45,9 W Manufacturer Johannes J. Matthies GmbH & Co. KGHammerbrookstr. 97 20097 Hamburg, GermanyHomepageDistributionoffroad-kontor

Set of 2 high-quality indicators for SW-MOTECH KOBRA hand guards (available separately). The indicators offer an increased visibility on-road and off-road and can be easily placed in the recesses of the a. m. hand guards. In order to convert any 10 or 20 watt indicators to the KOBRA LED ones featuring 1 watt, it is necessary to install an additional resistor set (available separately, see below). Specifications Delivered in pairs 16-LED indicators with an operating current of 12 volts and a 1-watt consumption per side Original indicators must be removed in order to install the LED ones Depending on the original flash frequency, it may be necessary to insert a corresponding resistor (available separately) in order to achieve the correct indicator frequency Delivery includes the necessary mounting instructions ECE test mark: E8 50R-001279

High-quality side stand bypass dongle by the US manufacturer VANASCHE MOTORSPORTS, suitable for the below-mentioned KTM and Husqvarna models. KTM/Husqvarna have gone to great lengths to provide a side stand sensor that cannot be tampered with by not allowing any gear engagement without the side stand in the "UP" position. In spite of the undisputed safety aspect, there are a few other issues. If this sensor is to fail (or the magnet lost) while in the field, the rider will be left stranded. However, this is not a simple roadside repair, like cutting the switch off and twisting wires together or even digging up a proper resistor to temporarily alleviate the problem. This is a 50% duty cycle square wave that would be almost impossible to duplicate without the proper hardware, an oscilloscope, and the necessary knowledge in circuits/electronics.   Carrying one of these dongles on the bike provides for a little piece of mind should the OEM product fail.  WARNING: This product is to be carried as a spare part and to be used to get rider and  bike to safety when the OEM sensor fails. It is NOT to be installed while the OEM side stand sensor is operating normally, as this allows the bike to engage gears with the side stand still in the down position which can result in property damage and/or injury. Suitable for:  Husqvarna 701 - Enduro                                     MY 2016 Husqvarna 701 - Enduro & SMC & Vitpilen        from 2021 - EU models KTM 690 - Enduro & SMC                                   from 2021 - EU models KTM 690 - Enduro                                               2008 - 2018 KTM 990 Adventure R/S                                     2006 - 2013 KTM 1190 Adventure/R                                        all Manufacturer Vanasche Motorsports61538 Ward Rd. Bend, OR 97702 , USAHomepageDistributionoffroad-kontor

High-quality side stand bypass dongle by the US manufacturer VANASCHE MOTORSPORTS, suitable for the below-mentioned models. KTM/Husqvarna/GasGas have gone to great lengths to provide a side stand sensor that cannot be tampered with by not allowing any gear engagement without the side stand in the "UP" position. In spite of the undisputed safety aspect, there are a few other issues. If this sensor is to fail (or the magnet lost) while in the field, the rider will be left stranded. However, this is not a simple roadside repair, like cutting the switch off and twisting wires together or even digging up a proper resistor to temporarily alleviate the problem. This is a 50% duty cycle square wave that would be almost impossible to duplicate without the proper hardware, an oscilloscope, and the necessary knowledge in circuits/electronics.   Carrying one of these dongles on the bike provides for a little peace of mind should the OEM product fail.  WARNING: This product is to be carried as a spare part and to be used to get rider and  bike to safety when the OEM sensor fails. It is NOT to be installed while the OEM side stand sensor is operating normally, as this allows the bike to engage gears with the side stand still in the down position which can result in property damage and/or injury. Suitable for:  Husqvarna 701 - Enduro & SMC & Vitpilen    2017-2021 US models Husqvarna 701 - Enduro & SMC & Vitpilen    2017-2020 EU models KTM 690 - Enduro & SMC                               2019-2021 US models KTM 690 - Enduro & SMC                               2019-2020 EU models KTM 690 - Duke                                               from MY 2016 KTM 1090 Adventure                                       all KTM 1290 Adventure                                       from MY 2017 GasGas 700 Enduro + SMC  Note: Regarding the KTM 690 and Husqvarna 701 EU models from MY 2021, the corresponding dongle can be puchased here! Manufacturer Vanasche Motorsports61538 Ward Rd. Bend, OR 97702 , USAHomepageDistributionoffroad-kontor

High-quality, compact 5-watt LED headlight by VISION X for universal applications. Perfect for on-the-go light. Specifications Die-cast 4.3 cm (1.7”) round aluminum housing Polycarbonate lens Radial fins for optimum head dissipation Weatherproof Deutsch connectors Water-proof according to IP68 standard Highest light output per cubic inch on the market (365 effective lumens) Only drawing 0.42 amps at 12 volts for an extremely low power draw Omni-link connecting 3 pods together available separately Compatible with selected Solo Pod accessories, such as handlebar mounts and battery packs Available with 10° - Narrow, 40° - Wide or 60° - Extra Wide beam pattern - please select from above Manufacturer VISION X LIGHTING1601 Boundary Blvd Auburn, WA 98001 USAHomepageDistributionVision X Europe188/5 Rue du Cerf 1332 Genval, BelgiumHomepage

High-quality flashlight set by VISION X, featuring two differently-sized LED torches. Specifications Delivery includes 1 small 5-LED and 1 large 30-LED flashlight Durable aluminum housings Simple on-off operation Non-slip touch and easy-to-handle 50,000 hour LED life span 24+ hour run time (depending on battery strength) Batteries NOT included! Manufacturer VISION X LIGHTING1601 Boundary Blvd Auburn, WA 98001 USAHomepageDistributionVision X Europe188/5 Rue du Cerf 1332 Genval, BelgiumHomepage

Functional, rechargeable LED work light by VISION X. Specifications Acrylic body Rubberized, anti-slip safety handle Integrated hook for hanging 120° LED beam for illuminating wide areas Delivery includes 12V cigarette lighter and 230V wall charger Manufacturer VISION X LIGHTING1601 Boundary Blvd Auburn, WA 98001 USAHomepageDistributionVision X Europe188/5 Rue du Cerf 1332 Genval, BelgiumHomepage

Functional combination mounting kit by VISION X including all mounts, ideal for fixing the VISION X Mini Solo LED to helmets and handlebars (Mini Solo not included - available separately, see below). Specifications  Ideal for use during biking trips in combination with the VISION X Mini Solo headlight and the corresponding VISION X battery Suitable for both professional and spare-time activities Compatible with selected other VISION X Solo accessories Manufacturer VISION X LIGHTING1601 Boundary Blvd Auburn, WA 98001 USAHomepageDistributionVision X Europe188/5 Rue du Cerf 1332 Genval, BelgiumHomepage

Mount for fixing the VISION X Mini Solo Compact 5-watt LED to 19-32 mm tubes (Mini Solo not included - available separately). Specifications Ideal for use during biking trips in combination with a Mini Solo headlight and the corresponding VISION X battery Suitable for both professional and spare-time activities Compatible with selected other VISION X Mini Solo accessories Manufacturer VISION X LIGHTING1601 Boundary Blvd Auburn, WA 98001 USAHomepageDistributionVision X Europe188/5 Rue du Cerf 1332 Genval, BelgiumHomepage

Functional combination mounting kit by VISION X including all mounts, ideal for fixing the VISION X Solstice Solo and Solo Prime LEDs to helmets and handlebars (Solstice Solo/Prime not included - available separately). Specifications  Ideal for use during biking trips in combination with VISION X Solstice Solo/Prime headlights and the corresponding VISION X battery Suitable for both professional and spare-time activities Compatible with selected other VISION X Solo accessories Manufacturer VISION X LIGHTING1601 Boundary Blvd Auburn, WA 98001 USAHomepageDistributionVision X Europe188/5 Rue du Cerf 1332 Genval, BelgiumHomepage

High-quality 10-watt LED headlight by VISION X for universal applications. Perfect for on-the-go light. Specifications Die-cast 5cm (2″) round aluminum housing Polycarbonate lens Radial fins for optimum heat dissipation Weatherproof Deutsch connectors Water-proof according to IP68 standard Integrated Electronic Thermal Management (ETM) PWM integrated dimming circuitry 90% optically pure Highest light output per cubic inch on the market Coloured LEDs available Omni-link connecting 3 pods together available separately Compatible with selected Solo Pod accessories, such as handlebar mounts and battery packs Available with 10° (Spot), 20° (Flood) and 40° (Ultra-Flood) beam patterns - please select from above Manufacturer VISION X LIGHTING1601 Boundary Blvd Auburn, WA 98001 USAHomepageDistributionVision X Europe188/5 Rue du Cerf 1332 Genval, BelgiumHomepage